About, ooooh, five months ago I decided to make my sproglet some bibs. He was six months old at the time and I wanted a bib of a decent length to actually catch all the food he was spilling down his front as I was weaning him.
After a very perfunctory Google, I couldn’t find the right kind of pattern online, most seeming to cater to smaller dribble-catching baby bibs, so I decided to make my own.
Now, I’m not claiming in any way to be any sort of sewing maven, but since I’d made the pattern I thought I’d share it here, in case it was useful for anyone else. Five months later, here it finally is!
The one good thing about my ridiculous delay in getting this ready to post is that I’ve had time to trial (and repeatedly wash) my original bibs, so I’ve made a few alterations to improve their durability.
The bib has a nice cotton fabric on the front, backed with terry towelling, which I’ve found really useful as all the food spills down the front and then you can use the back to wipe your baby clean once they’ve finished eating.
These instructions look amazingly lengthy, but it’s really a very simple process. I’ve just included lots of detail
because I can’t help waffling that I thought might be useful to someone who is new to sewing. Ditto with the seemingly excessive number of photographs…
- This pdf of the pattern
- Terry towelling fabric (this makes the back of the bib)
- Cotton fabric, either plain or patterned (this makes the front of the bib)
- Sewing machine or a lot more patience than I have and a needle and thread
- Iron-on velcro or some sew on poppers
What to do
- Print out the bib pattern onto two separate pieces of A4 (don’t use double sided as you need both of the pieces separately), cut out and sellotape together along the dotted lines.
- Pre-wash both of your fabrics so that they’ve done any shrinking in advance of being sewn together. Iron them flat. (I know, I hate ironing too, and am always tempted not to do it…)
- Cut out one piece of the pattern in terry towelling and one in the cotton fabric. If your cotton fabric has a design on, make sure you line up the template so that you have the parts of the design where you’d like them to be in the bib… In the photo below, I had inadvertently cut off one of my cowboy’s heads, so I started again with the design aligned better (see the later photos). As a side note about the towelling fabric, it tends to shed hundreds of tiny little white bobbles everywhere when you cut it, so I find it useful to cut out over something I can easily shake off into the bin afterwards. (ie Not the sitting room carpet, like I did the first time I used it.)
- Place the two fabrics together, with the right side of the cotton facing inwards…
- …and pin around the outside
- Leaving a small gap to turn the bib inside out, sew around the outside, with a 1/2 inch seam allowance. (NB, I’ve found with the other bibs I’ve made that the terry towelling tends to fray a little, hence the slightly large seam allowance.)
- As an optional extra, you could also go around the seam with a zigzag stitch as well, just to prevent any fraying in the future…
- Turn the bib inside out, pushing the material through the hole you left
- You’ve now got a slightly puffy version of the finished bib.
- Iron the bib flat, making sure that your gap matches the rest with seam allowance.
- Leaving a 1/4 inch seam allowance, and starting and finishing with a small backstitch, sew all around the outside of the bib, which creates a neat-looking edge and closes the gap at the same time
- Cut all the loose threads.
- Now for the fastening. Cut a piece of Velcro the appropriate size for your neck edges. Position it in the right place and hold both sides of the neck fast.
- Then iron it into place, following the instructions for your brand of velcro. (Usually, this is something like, don’t iron directly onto the velcro and don’t use the steam settings. Leave the iron on place for about a minute to seal the glue.) Leave it to dry.
- If you’re planning on putting the bib in the washing machine and tumble dryer (and, let’s face it, I doubt many people want to hand wash bibs) you might find that the iron-on velcro isn’t that sturdy. Just in case, I sewed all round the velcro as well, completing a square around the outside and then two diagonal lines across the main section as well.
- Tadaaaaa! It’s all finished, and quite professional looking, even if I do say so myself:
Just perfect to hang out on the line and admire in the breeze…
You could leave the bib like this, or you could embellish the front. In my first bib bundle, I made a few with plain white fabric and then ironed on vintage images using the method outlined here. This gave me such beauties as this cabbage bib:
This time round, I decided to quilt the front of one of the bibs I made. (Since learning how to quilt, I’ve become a bit obsessed with it as a general idea…)
I just roughly went around the outlines of the fabric design, which looked really good afterwards. You can pick out details like this cowboy’s bum disappearing over the fence…
…or this cowboy’s head:
You could also try all sorts of other things, such as applique, or making the top fabric from patchwork. I’ve even seen some bibs for baby girls with rickrack sewn on to them… (Not my personal cup of tea, but each to their own.)
Despite lengthy instructions here, this really is a simple make. In fact, I suspect you could probably make a new bib in less time than it’s taken to read through to the end of this post…
If you do make one, I’d love to hear how you’ve got on. Please do leave me a comment below and let me know…
- Take a look at my first bundle of bibs for more fabric ideas
- If you were giving these as a present, I think they’d be great along with this quilted burp cloth…
- …or these gorgeous little baby trousers